Skip to content

Customer Approved Since 1942 — Family-Owned & Operated

Plumbing

Commercial Water Heater Installation in Salt Lake City

Towers PlumbingNovember 13, 20267 min read

A restaurant cannot run a dishwasher without hot water. A salon cannot wash hair, an office cannot keep restrooms comfortable and a multi-unit building will hear about it from every tenant before lunch. Commercial water heater installation in Salt Lake City is rarely urgent until the day the old unit fails, and that is exactly why it deserves planning.

This guide covers the decisions behind a commercial installation, from sizing to scheduling, so the work happens on your timeline. Towers Plumbing provides commercial plumbing for restaurants, offices, retail spaces and multi-unit buildings, including water heater work.

How commercial water heating differs from a home

A home water heater serves a handful of fixtures with predictable use. A commercial system serves peak demand, and peak demand varies by business. A restaurant may need large volumes during prep and cleanup. A gym has a rush of showers after the morning and evening crowds. An apartment building may see demand spread across many units but concentrated at certain hours.

Because of that, the question is not just how many gallons the tank holds. It is how much hot water the system can deliver in the busiest hour, and how quickly it recovers afterward. Sizing a commercial unit to the right capacity and recovery rate avoids two common problems: running out when it matters and paying to heat more water than you ever use.

The main options to consider

Storage tank systems. A large tank heats and holds water, ready for peak use. They are straightforward and handle surges well, and they take floor space and need periodic flushing.

Tankless systems. A tankless unit heats water on demand, which saves space and removes the standby tank. In a commercial setting, several units may be installed together to meet demand, and the gas supply, venting and electrical service must support them.

Boiler-fed or indirect systems. In buildings that already have a boiler, an indirect storage tank can use that heat source for domestic water.

Point-of-use heaters. In a building with one distant sink, a small local unit may be more efficient than extending hot water piping.

No option is automatically best. The right one depends on your usage pattern, the available fuel, the space and any health or code requirements for your type of business.

Need help sorting out the right system? Call Towers Plumbing at (801) 266-3529 and describe your building. Towers Plumbing is a licensed and insured, family owned company, and its team can talk through your building before any visit is scheduled.

What to gather before the installation visit

A plumber can give a better recommendation if you provide basic facts.

  1. The make, model and age of the current water heater, if there is one
  2. Which fixtures and equipment use hot water, and when demand peaks
  3. The fuel available, whether natural gas, electric or both
  4. The location of the unit, including clearances, venting and drain access
  5. Any special requirements, such as sanitizing temperatures for food service or code requirements

A photo of the data plate on the old unit is useful. So is a note about any recurring complaints, such as lukewarm water at the far end of the building.

Planning around your business hours

Water heater work interrupts service, so scheduling is part of the project. A good plan identifies a window when the building can be without hot water, arranges access for the crew and prepares tenants or staff in advance. For a restaurant, that may mean working before opening or on a closed day. For a multi-unit building, it may mean notifying residents of a specific time frame.

Ask the installer how long the hot water will be off, how the old unit will be removed and whether any temporary solution is available. If you plan the replacement before the old unit fails, you can choose the quiet time instead of reacting to an emergency.

Why commercial water heaters fail

Understanding how these units wear out helps you judge when replacement is near. In a storage tank, sediment settles at the bottom and forms a layer that the burner or element must heat through, which strains the tank and shortens its life. The sacrificial anode rod, a metal rod inside the tank that corrodes so the steel does not, is consumed over time, and once it is gone the tank lining begins to corrode instead.

Thermostats, gas valves, heating elements and the temperature and pressure relief valve are the other parts that wear out most often. A tank that leaks from its body rather than a fitting is usually finished, because the corrosion that caused it cannot be reversed.

Tankless units fail differently. Scale builds up on the heat exchanger and restricts flow, igniters and flow sensors wear out, and vents can clog. Heavy daily use speeds up all of these processes, which is why a busy kitchen often outpaces the service life of the same model in a quiet office.

A scenario, the owner of a small duplex

Not every commercial water heater serves a restaurant. Picture the owner of a small duplex with two tenants who shares a single large storage heater in a utility closet. One morning both tenants report lukewarm showers, and the owner finds water pooling around the base of the tank.

The pooling water points to a failed tank rather than a loose fitting, so the right response is to shut off the cold supply and the fuel to the heater, then call a plumber for replacement rather than repair.

Because two households depend on that heater, the owner also needs to decide whether one larger unit or a different arrangement serves the building better. Planning ahead turns a crisis into a scheduled project.

A second scenario, the homeowner with a home business

Commercial-grade equipment is not only for storefronts. Consider a homeowner who runs a small home-based daycare or pet grooming business from a converted garage and has added a second water heater to keep up. When that extra heater starts rumbling and the water turns lukewarm, the homeowner has to decide whether to flush the tank, repair it or replace it.

Checking the age on the data plate, looking for rust at the base and asking a plumber about the anode rod are sensible first steps. For a household that now depends on hot water for both family and income, a planned replacement avoids the stress of failing at the worst moment.

What the installation itself involves

Installation is more than swapping one unit for another. The installer shuts off supply, drains and disconnects the old heater and checks the condition of connected piping and valves. The new unit is set, connected and vented according to its type, with a relief valve and discharge piping. Gas lines, electrical service and condensate drains are verified. After filling and startup, the plumber tests operation, checks for leaks and sets the temperature appropriate to the use.

Commercial code may require specific components, such as expansion tanks or backflow protection. A plumber familiar with commercial systems will build those into the plan.

Keeping a commercial water heater running well

A maintenance plan prolongs the life of the unit and warns you before it fails. Regular tasks include flushing sediment from storage tanks, inspecting relief valves and checking burners, elements and controls. Tankless units need periodic descaling, depending on water conditions. Keeping a record of service helps you notice patterns.

Commercial water heater installation in Salt Lake City starts with a plan

If your water heater is aging, noisy or struggling to meet demand, now is a better time to plan than the day it fails. Call Towers Plumbing at (801) 266-3529 to discuss your building and your options. You can also read about water heater service on the Towers Plumbing site.

Need Help Now?

Don't wait — schedule your plumbing service today. Free estimates, upfront pricing.